Blown-In Insulation in Schertz, TX

The measured difference: cellulose delivers about R-3.7 per inch against roughly R-2.5 per inch for fiberglass, so hitting the same R-value target takes noticeably more inches of fiberglass. Each material has documented trade-offs. Cellulose packs denser and resists air drift through the blanket, but it's heavier and settles more; loose-fill fiberglass is lighter, barely settles, and won't wick water if the attic leaks. We work from each material's coverage chart and blow to its own correct install depth, because they are not interchangeable inch-for-inch.

Settling is the documented reason: loose fill compresses after install, cellulose more than fiberglass, so day-one depth and week-six depth are two different measurements. Our method installs above the final R-target so the SETTLED depth still meets spec once the blanket compresses. A crew that blows only to target on day one leaves you short after settling, and that shortfall is one of the most common ways a loose-fill job quietly under-delivers.

No, and understanding this limit is the whole diagnosis. Loose fill is a conductive barrier, slowing heat that moves through it, while air keeps leaking straight through at top-plate gaps, can lights, and penetrations. Blow it over an unsealed attic and the material just filters the escaping air. Air-sealing is its own separate step and it belongs first; the blow addresses conduction, never leakage.

In most cases yes, as a top-off, once we verify the existing layer is dry, intact, and free of mold or matting. Loose fill drapes over old fill without issue, and we blow added depth until the total reaches target. Where the old layer has settled flat or been crushed by foot traffic, we re-fluff or re-level it first, so the new material isn't sitting on a dead, compressed base.

The material's entire advantage rides on it: a seamless blanket that conforms around joists and wiring with no gaps, which holds true only at an even depth and the right machine density. Under-fluffed or thin-at-the-edges fill leaves documented cold spots. Our verification method is concrete: dam the eaves, dial the blower density, and staple depth-marker rulers across the deck, so the installed inches are a measurement you can read yourself rather than a number we promise.

Three things, in the order we actually find them: the damper, since fifty years of rust either seizes them or lets them hang open; the flue joints, because the clay tile holds up while the mortar between tiles erodes; and the crown. The firebox brick itself usually just needs its joints struck. None of it is exotic. A photographed inspection puts numbers and pictures on all three.

Depends how you'll use it. If you burn wood regularly, a stainless liner sized to the firebox restores full function and safety — real money, but a permanent fix. If you light a few fires a year for the look of it, vented gas logs in the existing flue often make more sense and cost less. We'll price both without leaning on you. There's no wrong answer here, just wrong salesmen.

Broadly, the farther east and south you go off the limestone edge, the more clay content and the more seasonal swell-shrink we find; closer to the Balcones side, footings sit near rock and barely move. But lots vary house to house — fill dirt, drainage, and tree roots matter as much as the geology map. We check the stack for plumb and measure instead of guessing by ZIP code.

Yes — our crews cover Schertz's 3 ZIP codes across Guadalupe County, including The Crossvine, Greenshire, Carolina Crossing, plus the surrounding communities.

We offer same-week scheduling across Schertz, booked by a real person in under two minutes, 7 AM to midnight every day.

Schertz is established-to-new Guadalupe-County suburbia — The Crossvine, Greenshire — between San Antonio and New Braunfels, so the inspection documents prefab condition on the newer stock and masonry-plus-clay-liner status on the older homes. Blown-In Insulation is part of keeping that local housing stock safe, efficient, and up to code.

Blown-In Insulation in Schertz starts from $1,650, but the honest number depends on what a craftsman finds on site — we won't quote premium work blind. A CSIA-certified technician inspects the actual condition, then hands you an itemized, transparent written quote tied to the findings and built to one national standard. No teaser pricing, no surprises. Call (214) 444-8103 for a free, no-pressure Schertz quote.

Yes — we run same-week and emergency blown-in insulation across Schertz, scheduled by a real person 7 AM to midnight every day. For an active chimney hazard, call (214) 444-8103 and we prioritize Schertz dispatch so a craftsman is on it fast.

Our Schertz crew lives in and works the metro across Guadalupe County, including The Crossvine, Greenshire, Carolina Crossing — a certified, local blown-in insulation team genuinely near you, holding the same national craftsmanship standard on every job, not dispatched cold from another city. Call (214) 444-8103.